HB1-P valve springs

Tubas, euphoniums, mouthpieces, and anything music-related.
Forum rules
This section is for posts that are directly related to performance, performers, or equipment. Social issues are allowed, as long as they are directly related to those categories. If you see a post that you cannot respond to with respect and courtesy, we ask that you do not respond at all.
Post Reply
tubameister
Posts: 15
Joined: Sat Aug 22, 2020 12:15 pm
Has thanked: 0
Been thanked: 2 times

HB1-P valve springs

Post by tubameister »

I own an old Hirsbrunner HB1-P and the valves are in great condition, but pushing them down takes a little more effort than I wish it did. I’m thinking maybe new valve springs might help this. The ones in their are very old and seem pretty stiff. Is my thought right? I’ve read that people like to use Yamaha Euphonium valve springs on their tubas. Is this worth looking into? Thank you for any help you may be able to offer!


User avatar
bloke
Mid South Music
Posts: 19342
Joined: Thu Aug 13, 2020 8:55 am
Location: western Tennessee - near Memphis
Has thanked: 3854 times
Been thanked: 4105 times

Re: HB1-P valve springs

Post by bloke »

The Yamaha euphonium springs are probably plenty strong for old smaller Nirschl valves, which you probably have.

I would still rate them as marginally strong enough for the large valves that replaced them.

I would also rate the euphonium springs as strong enough for lighter weight Meinlschmidt aftermarket pistons.
User avatar
the elephant
Posts: 3403
Joined: Thu Aug 13, 2020 8:39 am
Location: 404 - Not Found
Has thanked: 1902 times
Been thanked: 1345 times

Re: HB1-P valve springs

Post by the elephant »

Bloke pioneered this for the awfully heavy MW "Big Valve" piston set to try and make them less fatiguing to use. They work well with these valves if perhaps a little bit light for my tastes.

I finally tried them in both of my piston horns, both of which have the nicer (IMHO) pistons made by Walter Nirschl and used on a lot of different tubas over the years. These valves are a bit lighter so the fatigue factor is less important. However, I wish I had switched to these springs years ago. While they are a bit too soft for my taste on the Big Valve sets they are wonderful on my Nirschl valve sets.

I think you ought to give them a try. They are under $20 for four.

https://www.amazon.com/gp/product/B01MXFTW8C
Image
User avatar
the elephant
Posts: 3403
Joined: Thu Aug 13, 2020 8:39 am
Location: 404 - Not Found
Has thanked: 1902 times
Been thanked: 1345 times

Re: HB1-P valve springs

Post by the elephant »

… aaaaand bloke beat me to the punch.

There you go. I gave you the link. Now BUY a set and try them out. They are drop-in replacements for Nirschl-made valves, fitting the relief in the bottom caps nicely.
Image
tubameister
Posts: 15
Joined: Sat Aug 22, 2020 12:15 pm
Has thanked: 0
Been thanked: 2 times

Re: HB1-P valve springs

Post by tubameister »

Thank you guys so much for your help!
These users thanked the author tubameister for the post:
the elephant (Thu Nov 25, 2021 8:28 pm)
tubameister
Posts: 15
Joined: Sat Aug 22, 2020 12:15 pm
Has thanked: 0
Been thanked: 2 times

Re: HB1-P valve springs

Post by tubameister »

My new valve springs came in today and I thought I’d give an update. Upon first look I didn’t think they were going to be a good fit because they were quite a bit shorter than the old valve springs. I figured the valves would sag in because of this but I was happily surprised to see that they did not. You can really tell how worn out the old springs were. Thank you so much for your help again!
These users thanked the author tubameister for the post:
the elephant (Wed Dec 01, 2021 6:52 pm)
User avatar
the elephant
Posts: 3403
Joined: Thu Aug 13, 2020 8:39 am
Location: 404 - Not Found
Has thanked: 1902 times
Been thanked: 1345 times

Re: HB1-P valve springs

Post by the elephant »

:smilie8:
Image
Post Reply