knocked out two tenor saxophone repairs and one baritone saxophone repair yesterday until late and into today, in spite of also entertaining and cooking for my houseguest…average: $200 per repair.
I combined errands near that school of banking, picking up a repaired trailer, buying new 16 foot boards for same trailer, and delivering the saxophones today. Yet another saxophone had been kicked, which had been previously been set on the ground (not a good idea). I saw that the octave key was barely out of adjustment because the neck had been bent down, I rebent the neck, adjusted the octave key, shrugged my shoulders, and handed it back to them.
I’m pretty sure this is the way to keep school repair accounts.
school repairs:
Hey: Their money spends, and they eventually pay. As long as I don’t have some boss to take half of my earnings (before the government takes the other half), I’ll be OK.
Mrs. bloke
- bloke
- Mid South Music
- Posts: 19342
- Joined: Thu Aug 13, 2020 8:55 am
- Location: western Tennessee - near Memphis
- Has thanked: 3854 times
- Been thanked: 4105 times
- Three Valves
- Posts: 4608
- Joined: Thu Aug 13, 2020 4:07 pm
- Location: The Land of Pleasant Living
- Has thanked: 815 times
- Been thanked: 501 times
Re: Mrs. bloke
No matter how bad her day was, it was probably better than my day working for The Man!!
Thought Criminal
Mack Brass Artiste
TU422L with TU25
1964 Conn 36k with CB Arnold Jacobs
Accent (By B&S) 952R with Bach12
The Fourth Estate is the Fifth Column
Mack Brass Artiste
TU422L with TU25
1964 Conn 36k with CB Arnold Jacobs
Accent (By B&S) 952R with Bach12
The Fourth Estate is the Fifth Column
- bloke
- Mid South Music
- Posts: 19342
- Joined: Thu Aug 13, 2020 8:55 am
- Location: western Tennessee - near Memphis
- Has thanked: 3854 times
- Been thanked: 4105 times
Re: Mrs. bloke
Today, she helped me replace these two boards (2X12X16, treated, wet, expensive, tight squeeze - other boards had NOT shrunk, several tricks involved in getting them in place). We also had to rout (redneck method - with a circular saw) those two places (seen), so those two metal bands would bolt back in place, below the surface. notice: Only the last (narrower) board on the right has a small space between it and the adjacent board. that one had to tuck in to both ends AND the side, so - when we originally installed all the boards - that one had to have a little room to shimmy it in place.Three Valves wrote: ↑Fri Aug 19, 2022 5:27 pm No matter how bad her day was, it was probably better than my day working for The Man!!
After that I loaded up the mower and took it to my friends house (who has a big gear-puller) so I could remove the played-out-after-all-these-years PTO (clutch) and bolt on a new one. ($260 - eBay - beats taking it to the JD dealer, and asking them to "fix what's wrong"...probably saving 80%...I could just imagine them charging me a grand for a new PTO and installation labor.)
(I'm thinking/hoping that the last little "stingy" place from all of that surgery is finally beginning to heal. I "felt" it once or twice today - barely - but no stinging...and I contorted myself and exerted myself a LOT, today. I was actually having to NOT take in as much as as I - sorta - needed sometimes, to play, to avoid irritating that "hurty" place.)
- These users thanked the author bloke for the post (total 2):
- Three Valves (Sat Aug 20, 2022 7:58 am) • windshieldbug (Sat Aug 20, 2022 11:37 am)