The "5-2-3-4 is horribly sharp for the pitch one whole step above the fundamental" problem solved (on ONE model of tuba)

Projects, repair topics, and Frankentubas
User avatar
bloke
Mid South Music
Posts: 19342
Joined: Thu Aug 13, 2020 8:55 am
Location: western Tennessee - near Memphis
Has thanked: 3854 times
Been thanked: 4105 times

Re: The "5-2-3-4 is horribly sharp for the pitch one whole step above the fundamental" problem solved (on ONE model of t

Post by bloke »

Kirley wrote: Sat Jan 14, 2023 1:57 am
bloke wrote: Thu Jan 12, 2023 9:20 am I'm getting closer and closer to a good solution. Widening/lengthening those bows - which double over - not only lowers the position of the fifth slide (right down next to the number one slide bow), but also offers an easier way to grab that slide with other fingers of the left hand which are already placed on the number one slide.. so I'm darn close to a workable on-the-fly smooth solution for playing a tuned double low C without resorting to a false tone.
You’ll be able to pull both slides (1&5) at the same time?
I've tried it a few times. It probably is going to require some practice if I need to do it but it seems possible.
Thankfully, double low C is rare, but - when it's encountered - I would like to be able to play it in tune and without using a false tone valve combination.


User avatar
bloke
Mid South Music
Posts: 19342
Joined: Thu Aug 13, 2020 8:55 am
Location: western Tennessee - near Memphis
Has thanked: 3854 times
Been thanked: 4105 times

Re: The "5-2-3-4 is horribly sharp for the pitch one whole step above the fundamental" problem solved (on ONE model of t

Post by bloke »

...so this is the o.e.m. config (prior to my re-config) of the #5 slide

- three very narrow slide bows
- one slide (loop-over did not slide)
- sat in this very high/pulled-out position for default tuning (very low E, E-flat, D-flat, B-natural)
>> not enough slide tubing remaining to pull out for very low C
>> impossible to quickly grasp - after releasing the #1 slide, anyway

The pull was so much, that I tend to wonder what they were thinking.

Image
User avatar
arpthark
Posts: 3923
Joined: Mon Aug 24, 2020 4:25 pm
Location: Southeastern Connecticut
Has thanked: 956 times
Been thanked: 1074 times
Contact:

Re: The "5-2-3-4 is horribly sharp for the pitch one whole step above the fundamental" problem solved (on ONE model of t

Post by arpthark »

bloke wrote: Sat Jan 14, 2023 8:04 am The pull was so much, that I tend to wonder what they were thinking.

Image
Push it in all the way, tape the 5th valve down, pull out all the other slides and you've got an Ab tuba?

For those low excerpts, ya know.
User avatar
bloke
Mid South Music
Posts: 19342
Joined: Thu Aug 13, 2020 8:55 am
Location: western Tennessee - near Memphis
Has thanked: 3854 times
Been thanked: 4105 times

Re: The "5-2-3-4 is horribly sharp for the pitch one whole step above the fundamental" problem solved (on ONE model of t

Post by bloke »

now:
Push it in all the way (BOTH of it's slides), mash down 1 & 5, and I can rattle the walls with an in-tune (rather than "tending-to-ride-high") low F-sharp...

...but I'm going to reconfigure #3, so that I can pull it out about 5/8" further (currently: remarkably short slide tubes) and do the same thing.
arpthark wrote: Sat Jan 14, 2023 10:06 am
bloke wrote: Sat Jan 14, 2023 8:04 am The pull was so much, that I tend to wonder what they were thinking.

Image
Push it in all the way, tape the 5th valve down, pull out all the other slides and you've got an Ab tuba?

For those low excerpts, ya know.
Post Reply